open TELEMAC-MASCARET The mathematically superior suite of solvers

Hello everyone
I am doing a small case in TELEMAC 3D, with Temperature, I ran an already exchange case with the wind, pressure constant and also changing in time.
But I was wondering two things:
1. How is manage the inflow heat through the surface (air7water) in the boundary conditions?
2. Where Can I change or find this Coefficients β, T, ρ? (equation of state )

Hi Julie

The heat through the surface is managed in the bord3d.f subroutine which call the calcs3d_thermics.f subroutine in waqtel module...

For the coefficients I think they are in the drsurr.f subroutine

Hope this helps

Dear Julie,

In addition there are some information in the waqtel (thermic) and telemac3d (active tracers) user manuals: wiki.opentelemac.org/doku.php?id=documentation_v8p1r0

Best regards,

Right now my model is not working anymore, I don't know what else to do.

In attachment, there are my simulations files.
And the output file with the error.

Thx in advance.

Hello,

Which version are you using? I assume an older one than v8p1 (every keyword with VERTICAL VELOCITY has been deleted).

Anyway, without the whole set of input files and the correct names in the steering file, it is difficult to reproduce your error.

I have not seen the output file either.

Chi-Tuan

Hi, I am using the v7p2r3 version.
Okay, I will attach all files.
Thank you very much

Geometry

cas file

Boundary conditions


fortran file

txt file with Hydroclimatological series

water quality cas file

2D simulations

The out file


Thx

The error.

I don't know why the fil not e is summit
Anycase:
PLANTE: PROGRAM STOPPED AFTER AN ERROR
RETURNING EXIT CODE: 2
_____________
runcode::main:
:
|runCode: Fail to run
|/PRODCOM/Ubuntu16.04/mpich/mpich-3.2.0/gccgfortran/bin/mpiexec -wdir /work/jalzateg/Rejet_mesh/cas_rejet_exchange.cas_2020-04-10-19h03min53s -n 16 /work/jalzateg/Rejet_mesh/cas_rejet_exchange.cas_2020-04-10-19h03min53s/out_condim_exchange
|~~~~~~~~~~~~~~~~~~
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_INVALID_FLAG IEEE_UNDERFLOW_FLAG IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_INVALID_FLAG IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_INVALID_FLAG IEEE_UNDERFLOW_FLAG IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|Note: The following floating-point exceptions are signalling: IEEE_DENORMAL
|STOP 1
|~~~~~~~~~~~~~~~~~~





Thx

Hello,

You have already sent the same 6 input files, but the FICHIER POUR SUITE 2D is still missing (at least)...

Moreover, there may be a problem with the extension or the size of the output and error files. If not a .txt extension, try to resend the files with this extension, because nothing appears at the moment on the website.
If they are too big (which size?), you can try to zip the 2 of them and resend (it is only ASCII files).

Chi-Tuan