TELEMAC-MASCARET Forum: PROBLEM CREATING BOUNDARY CONDITIONS (conlim) (2/2)

Welcome, Guest

Page:
1
2

TOPIC: PROBLEM CREATING BOUNDARY CONDITIONS (conlim)

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36844

Dottarelli

Hi Martin,

Thanks a lot for your reply, it drives me to the solution of the issue.

Looking at the nodes where the problem occur, I found out that in one of the meshes the coordinates of a node does not match with the same node of the other meshes(I don't know why seeing that I used the same line, but I guess I made a mistake somewhere).

So I edited them (changing the coordinates) and then merged again and now it works properly!!

Thanks again for the attention you gave me.

Regards,
Andrea

The administrator has disabled public write access.

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36845

a.barton OFFLINE Moderator Posts: 683 Thank you received: 178	Sorry you have experienced this. If there is a bug in Blue Kenue it would be nice to try and get it fixed. As a first step, I would need to narrow down the issue and create something that I can reproduce here on my end. Are you willing to spend some time helping me build something that can be reproduced? I am currently using BK 3.11.13... likely you are using something older... Kindly, Alan
	The administrator has disabled public write access.

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36846

a.barton OFFLINE Moderator Posts: 683 Thank you received: 178	If you can share your outlines from post #36842 and the options you used when meshing then I can try what you tried... step-by-step... Kindly, ALan
	The administrator has disabled public write access.

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36848

Serrer OFFLINE Moderator Posts: 720 Thank you received: 304	Hi Andrea, Well that is good news indeed. Glad you sorted it out. It would be interesting though to see exactly where the failure occurred. Seems to me that you had the same or at least a similar issue while meshing the lagoon last week. Incidentally I was not able to replicate the problem with the files you posted. Cheers... Martin
	The administrator has disabled public write access.

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36849

Dottarelli	Hello Alan and Martin, I made something like a report, in which I describe step by step what I did and the problem found. Hope this help. Regards, Andrea Attachments: Report.pdf (344KB) File_report.zip (1,223KB)
	The administrator has disabled public write access.

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36869

a.barton OFFLINE Moderator Posts: 683 Thank you received: 178	Thank you for taking the time to write up a report and provide the files. At the moment I can't look into it; but I have created a ticket on CHyMS to track this issue to resolution. You may find the ticket here: - chyms.nrc.gc.ca/trac/BlueKenue/ticket/10 Kindly, Alan
	The administrator has disabled public write access. The following user(s) said Thank You: Dottarelli

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36875

Serrer OFFLINE Moderator Posts: 720 Thank you received: 304	Alan, Andrea is still using V3.3.4 (circa 2012) I suspect that we sorted this bug before I left and that's why I can't reproduce it here. Andrea, I suggest you try using the latest version. Cheers... Martin
	The administrator has disabled public write access. The following user(s) said Thank You: Dottarelli

PROBLEM CREATING BOUNDARY CONDITIONS (conlim) 4 years 1 month ago #36881

Dottarelli	Thanks Alan and Martin for your attention, Indeed I'm using a quite old version, I will update it as soon as possible. Sorry for the bothering you about an old version of the software. Regards, Andrea
	The administrator has disabled public write access.