Welcome, Guest
Username: Password: Remember me

TOPIC: Error on couuti.f , venuti.f

Error on couuti.f , venuti.f 6 years 1 month ago #31772

  • Papadimitriou
  • Papadimitriou's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 80
  • Thank you received: 3
Dear all,

I am trying to use the user specified formatted file to read external current and wind data varying in space and time using a modified couuti.f subroutine (I am also trying to do the same for wind). However I am noticing that while the reading and spatial interpolation is done properly only the first time step is read. While searching in the forum, I noticed that maybe the problem lies with the noudon.f subroutine and not couuti.f, so I used the modifed noudon.f specified in this topic (www.opentelemac.org/index.php/community-...-with-venuti-f#14671) but to no avail.

On a side note, contrary to venuti.f the times TC1 and TC2 are specified as INTENT(IN) and not (INOUT) and when I try to modify their values while changing the ty
The administrator has disabled public write access.

Error on couuti.f , venuti.f 6 years 4 weeks ago #31780

  • tfouquet
  • tfouquet's Avatar
  • OFFLINE
  • Moderator
  • Posts: 294
  • Thank you received: 112
Hello

If you specify stationary current = yes you can't have it varying in a file.
But beside that, even if you do not specify stationary current it won't work. The right way to do it is consideration of tide = Yes.
Then you construct your currant the way you did it and specify a heigth in anamar

regards

T.
The administrator has disabled public write access.

Error on couuti.f , venuti.f 6 years 4 weeks ago #31782

  • Papadimitriou
  • Papadimitriou's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 80
  • Thank you received: 3
Thank you Thierry for the reply,

Won't there be a confliction with the output variables between couuti.f and anamar.f since when anamar is called UC,VC have to be specified while with couuti the variables UC1,UC2,VC1,VC2 variables are calculated. If I leave the variables UC,VC undefined in anamar.f I get NaN results which I suspect don't stem from the couuti.f specification , since the model at least read the first time step before.

Regards,
Andreas
The administrator has disabled public write access.

Error on couuti.f , venuti.f 6 years 3 weeks ago #31831

  • Papadimitriou
  • Papadimitriou's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 80
  • Thank you received: 3
Dear all,

I am returning once again in this topic because it is quite concerning for my project. Following Thierry's suggestions I specified a tidal water level file to be read by maruti.f and a seperate currents file read by couuti.f. However even if I set the consideration of tide = YES the model as can be inspected in the output.txt file ignores the current velocities file and defaults to anamar.f where the velocities are set to 0. If I set consideration of tide = NO and I set the CONSIDERATION OF A STATIONARY CURRENT = YES then the velocities are read from the current file. The other time steps except the first are not read however at this point it is more important to locate why there is a conflict between the water level and velocities

Thank you for your assistance,
Kind regards,
Andreas
The administrator has disabled public write access.

Error on couuti.f , venuti.f 6 years 3 weeks ago #31833

  • tfouquet
  • tfouquet's Avatar
  • OFFLINE
  • Moderator
  • Posts: 294
  • Thank you received: 112
Hello
I made it work on your case but i had to change things around user format in tomawac, some things were not correct.

so you will find attached the fortran i had modified and yours.

hope it helps
Attachments:
The administrator has disabled public write access.

Error on couuti.f , venuti.f 6 years 3 weeks ago #31836

  • Papadimitriou
  • Papadimitriou's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 80
  • Thank you received: 3
Dear Thierry,

Thank you so much and for one last time can you help me because in the condiw subroutine you modified there doesn't seem to exist the declaration WAC_CPL_INIT and the DIM1 arguement.

I am using the version 7p3r0 and gfortran compiler

Regards,
Andreas
Attachments:
The administrator has disabled public write access.

Error on couuti.f , venuti.f 6 years 3 weeks ago #31837

  • tfouquet
  • tfouquet's Avatar
  • OFFLINE
  • Moderator
  • Posts: 294
  • Thank you received: 112
yes i sent the trunk version. If you are using V7P3 here are two subroutine you have to add.
Attachments:
The administrator has disabled public write access.
Moderators: tfouquet

The open TELEMAC-MASCARET template for Joomla!2.5, the HTML 4 version.