open TELEMAC-MASCARET The mathematically superior suite of solvers

Hi:
I had an error when interpreting TELEMAC-2D after installing the parallel version under Windows10 system . See the attachment for specific error information. So far I have not found the source of the error. Looking forward to having the same problem of peers to answer questions.
Thank you very much
All the best

no attachment

Error message for interpretation has been uploaded. Thank you very much

Error message while interpreting
“Compiling the program SPLITSEL and dependents
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

- completed: ...\v7p2r3\sources\utils\special\declarations_special.f
C:\opentelemac-mascaret\v7p2r3\sources\utils\special\plante.F:63: Error: Can't open included file 'mpif.h'
- completed: ...\v7p2r3\sources\utils\damocles\declarations_damocles.f
- completed: ...\v7p2r3\sources\utils\special\check_call.f
- completed: ...\v7p2r3\sources\utils\special\write_error.f
- completed: ...\v7p2r3\sources\utils\special\get_free_id.f
- completed: ...\v7p2r3\sources\utils\special\check_allocate.f
- completed: ...\v7p2r3\sources\utils\special\get_nodes_per_element.f
[\\\\\\\\\\\ ] 17% | 7s

Hummm ... I could not complete my work.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

compileTELEMAC::createObjFiles:
+> failed: gfortran -fopenmp -c -O3 -ffixed-line-length-132 -DHAVE_MPI -fconvert=big-endian -frecord-marker=4 -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\special -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\damocles -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\hermes -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\bief -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\splitsel C:\opentelemac-mascaret\v7p2r3\sources\utils\special\plante.F
... The following command failed for the reason above (or below)
gfortran -fopenmp -c -O3 -ffixed-line-length-132 -DHAVE_MPI -fconvert=big-endian -frecord-marker=4 -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\special -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\damocles -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\hermes -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\bief -I C:\opentelemac-mascaret\v7p2r3\builds\wing64mpi\lib\utils\splitsel C:\opentelemac-mascaret\v7p2r3\sources\utils\special\plante.F:

Hi
Source of error is indicate in the second line (error: can't open included file mpif.h)
So check the configuration to see if the location is ok

But in a more general way and as indicate in the rules, use the latest official version not a 3 years old one)

Hi c.coulet
Thank you for your reply. Another question is whether to copy the modified "system_v8p2r1_parallel.cfg" file into "C:\opentelemac-mascaret/v8p2r1/configs" when installing parallel version. Then the "compileTELEMAC.py" is interpreted.
All the best