Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username? Create an account
Forum
System Modules
TELEMAC-3D
(T3D COUPLED WITH WAQTEL) stops at the beginning of simulation
Flat Threaded

TOPIC: (T3D COUPLED WITH WAQTEL) stops at the beginning of simulation

(T3D COUPLED WITH WAQTEL) stops at the beginning of simulation 5 years 5 months ago #33730

  • sanaz
  • sanaz's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 69
  • Thank you received: 1
Hello,
I am trying to couple telemac3d with WAQTEL. However: it seams it stops without showing any error. I should mention that without coupling my model worked well.

Your help is very much appreciated!
Sanaz

================================================================================
ITERATION 0 TIME 0 D 0 H 0 MN 0.0000 S ( 0.0000 S)
================================================================================
MASS BALANCE
MASS BALANCE
INITIAL MASS OF WATER IN THE DOMAIN : 144737698838.29959

SOURCE POINT 1 PUT ON POINT
281758.75000000000 AND 5389740.5000000000
LOCATED AT 0.0000000000000000 METRES

SOURCE POINT 2 PUT ON POINT
279162.75000000000 AND 5395530.5000000000
LOCATED AT 0.0000000000000000 METRES

USING STREAMLINE VERSION 7.3 FOR CHARACTERISTICS
TELEMAC3D COUPLED WITH: WAQTEL
INITIALISATION BASED ON TPXO:
TPXO : WARNING:CONSTITUENT ID s1 IS NOT ALLOWED
C_ID( 1 ) = m2
C_ID( 2 ) = s2
C_ID( 3 ) = n2
C_ID( 4 ) = k2
C_ID( 5 ) = k1
C_ID( 6 ) = o1
C_ID( 7 ) = p1
C_ID( 8 ) = q1
C_ID( 9 ) = mm
C_ID( 10 ) = mf
C_ID( 11 ) = m4
C_ID( 12 ) = mn4
C_ID( 13 ) = ms4
C_ID( 14 ) = 2n2
C_ID( 15 ) = s1
- ACQUIRING LEVELS
- INTERPOLATING LEVELS
- ACQUIRING VELOCITIES
- INTERPOLATING VELOCITIES
END OF TPXO INITIALISATION
The administrator has disabled public write access.

(T3D COUPLED WITH WAQTEL) stops at the beginning of simulation 5 years 5 months ago #33731

  • sanaz
  • sanaz's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 69
  • Thank you received: 1
Hello,
I have increased the time step and it stopped after the following error:
I also attached my CAS fileS.

Thanks in advance,


================================================================================
ITERATION 0 TIME 0 D 0 H 0 MN 0.0000 S ( 0.0000 S)
================================================================================
MASS BALANCE
MASS BALANCE
INITIAL MASS OF WATER IN THE DOMAIN : 144737698838.30008

SOURCE POINT 1 PUT ON POINT
281758.75000000000 AND 5389740.5000000000
LOCATED AT 0.0000000000000000 METRES

SOURCE POINT 2 PUT ON POINT
279162.75000000000 AND 5395530.5000000000
LOCATED AT 0.0000000000000000 METRES

SOURCE POINT 1 PUT ON PLANE 1
LOCATED AT 1.9300651550291370E-003 METRES
SOURCE POINT 2 PUT ON PLANE 1
LOCATED AT 4.4203376770020064E-003 METRES
USING STREAMLINE VERSION 7.3 FOR CHARACTERISTICS
TELEMAC3D COUPLED WITH: WAQTEL
INITIALISATION BASED ON TPXO:
TPXO : WARNING:CONSTITUENT ID s1 IS NOT ALLOWED
C_ID( 1 ) = m2
C_ID( 2 ) = s2
C_ID( 3 ) = n2
C_ID( 4 ) = k2
C_ID( 5 ) = k1
C_ID( 6 ) = o1
C_ID( 7 ) = p1
C_ID( 8 ) = q1
C_ID( 9 ) = mm
C_ID( 10 ) = mf
C_ID( 11 ) = m4
C_ID( 12 ) = mn4
C_ID( 13 ) = ms4
C_ID( 14 ) = 2n2
C_ID( 15 ) = s1
- ACQUIRING LEVELS
- INTERPOLATING LEVELS
- ACQUIRING VELOCITIES
- INTERPOLATING VELOCITIES
END OF TPXO INITIALISATION
GRACJG (BIEF) : EXCEEDING MAXIMUM ITERATIONS: 200 RELATIVE PRECISION: 0.3007251E-05
GRACJG (BIEF) : EXCEEDING MAXIMUM ITERATIONS: 200 RELATIVE PRECISION: 0.1282582E-04
Attachments:
The administrator has disabled public write access.

(T3D COUPLED WITH WAQTEL) stops at the beginning of simulation 5 years 5 months ago #33732

  • sanaz
  • sanaz's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 69
  • Thank you received: 1
I am sorry for reposting. I changed the listing print out to 1. after the 4th iteration it stops without any error:
================================================================================
ITERATION 3 TIME 0 D 0 H 0 MN 30.0000 S ( 30.0000 S)
================================================================================
VALUE OF THE TRACER 1 AT THE BOUNDARIES READ IN THE ASCII FILE
T
SOURCE POINT 1 PUT ON PLANE 1
LOCATED AT 1.9300651550291370E-003 METRES
SOURCE POINT 2 PUT ON PLANE 1
LOCATED AT 4.4203376770020064E-003 METRES
ADVECTION-DIFFUSION OF VELOCITIES STEP
ADVECTION-DIFFUSION OF VELOCITIES STEP
PROPAGATION AND DIFFUSION WITH WAVE EQUATION
PROPAGATION AND DIFFUSION WITH WAVE EQUATION
GRACJG (BIEF) : 4 ITERATIONS, RELATIVE PRECISION: 0.1064677E-10
POSITIVE DEPTHS OBTAINED IN 1 ITERATIONS
CALCULATION OF VERTICAL VELOCITY STEP
CALCULATION OF VERTICAL VELOCITY STEP
ADVECTION-DIFFUSION OF TRACERS
ADVECTION-DIFFUSION OF TRACERS
MURD3D_POS SCHEME: 14 10 ITERATIONS
DIFFUSION OF TRN1
GRACJG (BIEF) : 1 ITERATIONS, RELATIVE PRECISION: 0.8987938E-19
MURD3D_POS SCHEME: 14 10 ITERATIONS
DIFFUSION OF TRN2
GRACJG (BIEF) : 1 ITERATIONS, RELATIVE PRECISION: 0.6583543E-14
MURD3D_POS SCHEME: 14 10 ITERATIONS
DIFFUSION OF TRN3
GRACJG (BIEF) : SOLUTION X=0 BECAUSE L2-NORM OF B VERY SMALL: 0.000000
MASS BALANCE
MASS BALANCE

WATER
MASS AT THE PREVIOUS TIME STEP : 0.1447409E+12
MASS AT THE PRESENT TIME STEP : 0.1447428E+12
MASS LEAVING THE DOMAIN DURING THIS TIME STEP : -1924232.
ERROR ON THE MASS DURING THIS TIME STEP : -0.4820258E-03
FLUX BOUNDARY 1: 192381.2 M3/S ( >0 : ENTERING <0 : EXITING )

TRACER 1: TEMPERATURE , UNIT : C * M3)

ADVECTIVE FLUX THROUGH BOUNDARIES OR SOURCES : -2886557.
DIFFUSIVE FLUX THROUGH THE BOUNDARIES : -0.8079370E+21
MASS AT THE PREVIOUS TIME STEP : 0.5441694E+13
MASS AT THE PRESENT TIME STEP : 0.8059768E+22
MASS EXITING (BOUNDARIES OR SOURCE) : -0.8079370E+22
ERROR ON THE MASS DURING THIS TIME STEP : 0.1960200E+20

TRACER 2: SALINITY , UNIT : G/L * M3)

ADVECTIVE FLUX THROUGH BOUNDARIES OR SOURCES : -5386672.
DIFFUSIVE FLUX THROUGH THE BOUNDARIES : -0.000000
MASS AT THE PREVIOUS TIME STEP : 0.4052745E+13
MASS AT THE PRESENT TIME STEP : 0.4052799E+13
MASS EXITING (BOUNDARIES OR SOURCE) : -0.5386672E+08
ERROR ON THE MASS DURING THIS TIME STEP : 0.4813865E-02

TRACER 3: CONCENTRATION , UNIT : % * M3)

ADVECTIVE FLUX THROUGH BOUNDARIES OR SOURCES : 0.000000
DIFFUSIVE FLUX THROUGH THE BOUNDARIES : -0.000000
MASS AT THE PREVIOUS TIME STEP : 0.000000
MASS AT THE PRESENT TIME STEP : 0.000000
MASS EXITING (BOUNDARIES OR SOURCE) : 0.000000
ERROR ON THE MASS DURING THIS TIME STEP : 0.000000

================================================================================
ITERATION 4 TIME 0 D 0 H 0 MN 40.0000 S ( 40.0000 S)
================================================================================
VALUE OF THE TRACER 1 AT THE BOUNDARIES READ IN THE ASCII FILE
T
SOURCE POINT 1 PUT ON PLANE 1
LOCATED AT 1.9300651550291370E-003 METRES
SOURCE POINT 2 PUT ON PLANE 1
LOCATED AT 4.4203376770020064E-003 METRES
ADVECTION-DIFFUSION OF VELOCITIES STEP
ADVECTION-DIFFUSION OF VELOCITIES STEP
PROPAGATION AND DIFFUSION WITH WAVE EQUATION
PROPAGATION AND DIFFUSION WITH WAVE EQUATION
GRACJG (BIEF) : 42 ITERATIONS, RELATIVE PRECISION: 0.9845686E-06
POSITIVE DEPTHS OBTAINED IN 1 ITERATIONS
CALCULATION OF VERTICAL VELOCITY STEP
CALCULATION OF VERTICAL VELOCITY STEP
The administrator has disabled public write access.

(T3D COUPLED WITH WAQTEL) stops at the beginning of simulation 3 months 3 weeks ago #45306

Hello , did you find the solution ?
I got the same error but coupling with tomawac
The administrator has disabled public write access.
Flat Threaded
Moderators: pham
Forum
System Modules
TELEMAC-3D
(T3D COUPLED WITH WAQTEL) stops at the beginning of simulation

The open TELEMAC-MASCARET template for Joomla!2.5, the HTML 4 version.