TELEMAC-MASCARET Forum: Model does not run in parallel mode (1/1)

Welcome, Guest

TOPIC: Model does not run in parallel mode

Model does not run in parallel mode 6 years 8 months ago #29361

Mustermann
OFFLINE
Expert Boarder
Posts: 268
Thank you received: 4

Hello,

At the moment I'm setting up a TOMAWAC model at the coast of Iceland. The model is still very basic but it does not run in parallel mode. I assume that is has either infinite solutions or the split up processes come up with slightly different solutions.
What could be the issue?

Thanks so much for help

Attachments:

The administrator has disabled public write access.

Model does not run in parallel mode 6 years 8 months ago #29362

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Hello, This is not a problem of parallelism, your configuration does not work in sequential mode either. Your boundary conditions file is wrong. BC2 file format is a BlueKenue format, you have to save it as *.cli file (conlim table file). Regards, Laurent
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 8 months ago #29370

Mustermann OFFLINE Expert Boarder Posts: 268 Thank you received: 4	Hello, Ohh sorry I uploaded accidentally the .bc2 file but of course I use the .cli file. But this does not work either. Regards, Clemens Attachments: bc_Horna_c...ides.cli (133KB)
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 8 months ago #29371

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Hello, Your configuration runs well on my personal computer in parallel mode with v7p2r1 of tomawac. What is the error message you have? Did you first try to run a validation case in parallel? Regards, Laurent
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 8 months ago #29372

Mustermann OFFLINE Expert Boarder Posts: 268 Thank you received: 4	Hej Laurent, It came out with an MPI error, but I tried to run it again and like you say it is running fine. Not sure what the problem was yesterday. Thank you for your help. Best - Clemens
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 8 months ago #29373

Mustermann OFFLINE Expert Boarder Posts: 268 Thank you received: 4	Hej Laurent, sorry I made a mistake the file I run was with just one processor and runs fine. Attached is the output regarding the failure. Attachments: Output_2018-03-23.txt (9KB)
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 7 months ago #29376

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	This seems to be a MPI error.. Are you sure MPI is well installed on your computer? Did you try to run a test case first? 2 workarounds are suggested at then of the error message, did you test them? Regards, Laurent
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 7 months ago #29377

Mustermann OFFLINE Expert Boarder Posts: 268 Thank you received: 4	Hej Laurent, I ran all test cases in parallel without any problems. The first suggestion work but I have to redo it always before I run the model another time. Maybe there is a more consistent workaround.
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 7 months ago #29378

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Ok, there is something strange with your mpi installation. Maybe you can also test the 2nd and 3rd fix suggested here: github.com/firemodels/fds/issues/5853 but if it does not work, I will not be able to help you anymore, sorry. Laurent
	The administrator has disabled public write access.

Model does not run in parallel mode 6 years 7 months ago #29379

Mustermann OFFLINE Expert Boarder Posts: 268 Thank you received: 4	Ok thanks I will check this. Will take me some time. Not sure if this is since I use the Intel MPI, but that should not be a problem. Thanks a lot Regards, Clemens
	The administrator has disabled public write access.