TELEMAC-MASCARET Forum: coupling tomawac telemac (2/3)

Welcome, Guest

Page:
1
2
3

TOPIC: coupling tomawac telemac

coupling tomawac telemac 5 years 4 months ago #34075

Hello Thierry,

thanks a lot, this helped me to go forwards.
But, i have another error msg.
i hope you help me further with errors, until i get this run.

i think it is related to the NUMBER OF TIME STEPS command.
It was´nt defined at first. so, i added this command but i still get the same error.

Please find attached the error message.

Thank you in advance!

best regards
Hatem

Attachments:

Black_sea_...n21s.txt (37KB)

The administrator has disabled public write access.

coupling tomawac telemac 5 years 4 months ago #34087

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Hi, The error message tells you that you didn't give a value to the keyword "NUMBER OF TIME STEP" in Tomawac steering file. Have a look at the section 8.2.7 of Tomawac user manual for time management and coupling period. I hope it helps. Regards, Laurent
	The administrator has disabled public write access.

coupling tomawac telemac 5 years 4 months ago #34089

tek	Hello, Thank you for your reply. i defined already the NUMBER OF TIME STEPS, which i calculated by: Duration/time step = 449280. But , i still get the same error. Please find attached case file and the file about the error. best regards, Hatem Attachments: TOMAWAC_CO...7-22.txt (5KB) Black_sea_...7-22.cas (5KB) Black_sea_...n16s.txt (38KB)
	The administrator has disabled public write access.

coupling tomawac telemac 5 years 4 months ago #34090

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Hi, You provide it in Telemac-2D steering file, but not in Tomawac steering file. Regards, Laurent
	The administrator has disabled public write access.

coupling tomawac telemac 5 years 4 months ago #34120

tek	Hello everyone, it doesn´t even compile if the NUMBER OF TIME STEPS is set in the TOMAWAC.txt (see attached). I´ll appreciate if someone could take time and go through the errors that will come up, and help me start my simulation (it´s for master thesis). It is about coupled Telemac2d-Tomawac simulation-run. the telemac 2d run succefully. regards, Hatem Attachments: 1.png (20KB)
	The administrator has disabled public write access.

coupling tomawac telemac 5 years 4 months ago #34121

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Hi, The right keyword is "NUMBER OF TIME STEP". Please, have a look to the user manuals and coupling examples. Regards, Laurent
	The administrator has disabled public write access. The following user(s) said Thank You: tek

coupling tomawac telemac 5 years 4 months ago #34122

tek	Thank you! But, i got another error message "hermes file not opened_err" (see attached). regards, Hatem Attachments: 2.png (22KB)
	The administrator has disabled public write access.

coupling tomawac telemac 5 years 3 months ago #34141

Leballeur OFFLINE openTELEMAC Guru Posts: 434 Thank you received: 163	Hi, This error occurs because the geometry and boundary conditions files are missing in the tomawac steering file. Please try first to run both models separately before coupling them. And have a look at the user manuals and examples. Regards, Laurent
	The administrator has disabled public write access. The following user(s) said Thank You: tek

coupling tomawac telemac 5 years 3 months ago #34142

tek	Thank you! i´ll look at the user manual, and try to fix it! regards Hatem
	The administrator has disabled public write access.

coupling tomawac telemac 5 years 3 months ago #34143

tek	Hi Laurent, the telemac model ran successfully. Now, im trying to fix the coupling between both (tomawac telemac) the simulation started, but it breaks up on the first time step ( see attached) Any idea what this error-msg means(CURRENT/WATER LEVEL FILE CANNOT BE USED AS INPUT FILE.) ? Regards , Hatem Attachments: 4.png (38KB)
	The administrator has disabled public write access.