TELEMAC-MASCARET Forum: Telemac3d error exit code 2 (1/1)

Welcome, Guest

TOPIC: Telemac3d error exit code 2

Telemac3d error exit code 2 9 months 2 weeks ago #44972

izzuansulaiman
OFFLINE
Fresh Boarder
Posts: 5

Hello everyone,

I am a beginner on telemac3d and need to model a river's flow.

After creating the .slf, .cli, and .cas files, I tried to run the simulation but got this error message (Attachments). I tried to solve it by changing the tidal boundary condition, but I think it has problems with my MPI. Anyway, it didn't work so I'm a bit lost, if anyone has any idea of how to solve it, it would be great.
Thank you !!

Attachments:

Telemac3derror.png (36KB)
Malacca_fi...rial.cas (4KB)

The administrator has disabled public write access.

Telemac3d error exit code 2 9 months 2 weeks ago #44973

c.coulet OFFLINE Moderator Posts: 3772 Thank you received: 1044	Just read well the 3 first line of the attachment... This is not a mpi problem...
	Christophe The administrator has disabled public write access.

Telemac3d error exit code 2 9 months 2 weeks ago #44974

izzuansulaiman OFFLINE Fresh Boarder Posts: 5	Hello. Thanks for your help! Currently, I already corrected the tide condition but the same error appeared. Do I have a problem with my BlueKenue file? Attachments: telemac3derror1.png (23KB)
	The administrator has disabled public write access.

Telemac3d error exit code 2 9 months 2 weeks ago #44975

c.coulet OFFLINE Moderator Posts: 3772 Thank you received: 1044	don't see any problem in the latest screenshot
	Christophe The administrator has disabled public write access.

Telemac3d error exit code 2 9 months 2 weeks ago #44976

izzuansulaiman OFFLINE Fresh Boarder Posts: 5	This one. Thanks! Attachments: telemac3derror2.png (110KB)
	The administrator has disabled public write access.

Telemac3d error exit code 2 9 months 2 weeks ago #44977

c.coulet OFFLINE Moderator Posts: 3772 Thank you received: 1044	This is a problem of your steering file. The keyword indicated at the first line require 2 values but you gave only 1...
	Christophe The administrator has disabled public write access. The following user(s) said Thank You: izzuansulaiman

Telemac3d error exit code 2 9 months 2 weeks ago #45048

izzuansulaiman OFFLINE Fresh Boarder Posts: 5	Hi c.coulet! Thanks again for your help. I fixed the exit code 2 issue by changing the value to 2;2. However, a new error message has popped up. Any suggestions or advice you could give me on my steering file would be greatly appreciated. Thanks! Attachments: Telemac3d.png (143KB) Malacca_fi...6-20.cas (4KB)
	The administrator has disabled public write access.

Telemac3d error exit code 2 9 months 2 weeks ago #45049

c.coulet
OFFLINE
Moderator
Posts: 3772
Thank you received: 1044

Not easy to identify the problem...
I think you should start with a simpler steering file and complexify it step by step...
Maybe as a very first trial, you could run a test in 2D for short time to check the initial tidal condition and the first time step...

Once it's ok, move to 3D always with a small duration, with small graphic and listing printout period...

In my opinion, 3 planes is a small value even it should work, maybe you have to look at this point and also the vertical discretization.

Same for the turbulence, start with constant viscosity and upgrade to K-eps later...

Hope this helps

Christophe

The administrator has disabled public write access.

The following user(s) said Thank You: izzuansulaiman