open TELEMAC-MASCARET The mathematically superior suite of solvers

When I simulating an example according to the RIVER clum ,It shows the error .



MESH: MESH ALLOCATED

*************************************
* END OF MEMORY ORGANIZATION: *
*************************************

INITIALIZING TELEMAC2D FOR
CALLING LECLIM
BACK FROM LECLIM
CALLING INBIEF
INBIEF (BIEF): NOT A VECTOR MACHINE (ACCORDING TO YOUR DATA)
FROPRO: FRONTAL PRODUCT REQUIRES A
RENUMBERING OF POINTS WITH STBTEL

PLANTE: PROGRAM STOPPED AFTER AN ERROR
RETURNING EXIT CODE: 2




the cas.file is showed below
/

---

/
/ STEERING FILE OF TELEMAC 2D
/ 'xiaoling' TEST-CASE
/
/ PAS DE TEMPS DE 4 s : 86 s
/ PAS DE TEMPS DE 8 s : 44 s 5.6 04/10/2004
/
/ HP C3700 compilateur HP : 44 s version 5.7 19/04/2007
/ HP C3700 compilateur Nag: 112 s version 5.7 19/04/2007
/
/ HP C3700 compilateur HP : 42 s version 5.8 26/11/2007
/ HP C3700 compilateur Nag : 107 s version 5.8 26/12/2007
/ Dell 2.8 GHz Linux compilateur pgi : 32 s version 5.8 19/12/2007
/
/ HP C3700 compilateur HP : 43 s version 5.9 16/10/2008
/ HP C3700 compilateur Nag : 105 s version 5.9 17/10/2008
/ Dell 2.8 GHz Linux compilateur pgi : 30 s version 5.9 16/10/2008
/
/ HP C3700 compilateur HP : 42 s version 6.0 24/11/2009
/ HP C3700 compilateur Nag : 102 s version 6.0 27/11/2009
/ Dell 2.8 GHz Linux compilateur Intel : 23 s version 6.0 26/11/2009
/
/ Version 6.2
/
/ HP C3700 compilateur HP : 47 s 04/05/2012
/
/

---

/
/ INITIAL CONDITIONS IF NOT COMPUTATION CONTINUED
/ DO 10 I=1,NPOIN
/ H%R(I) = MAX( 1.D0 , 23.77D0-ZF%R(I) )
/10 CONTINUE
/
BOUNDARY CONDITIONS FILE : geo_xiaoling.cli
GEOMETRY FILE : geo_xiaoling.slf
/PREVIOUS COMPUTATION FILE : ini_xiaoling.slf
RESULTS FILE : r2d_xiaoling.slf
/LIQUID BOUNDARIES FILE : t2d_xiaoling.qsl
/
/

---

/
/ GENERAL OPTIONS
/

---

/
TITLE = 'TELEMAC 2D : RIVER xiaoling'
COMPUTATION CONTINUED :NO
INITIAL TIME SET TO ZERO : YES
/TIME STEP = 8.
TIME STEP = 2.
NUMBER OF TIME STEPS = 27000
GRAPHIC PRINTOUT PERIOD : 250
LISTING PRINTOUT PERIOD = 1500
VARIABLES FOR GRAPHIC PRINTOUTS : 'U,V,S,B,H'
LAW OF BOTTOM FRICTION = 3
FRICTION COEFFICIENT = 30.
VELOCITY DIFFUSIVITY = 2.
TURBULENCE MODEL : 1
SOLVER ACCURACY = 1.E-4
/SOLVER : 7 SOLVER OPTION : 2 PRECONDITIONING : 2
IMPLICITATION FOR DEPTH = 1.
IMPLICITATION FOR VELOCITY = 1.
INITIAL CONDITIONS : 'CONSTANT ELEVATION'
INITIAL ELEVATION : 7.
PRESCRIBED FLOWRATES : 0.5 ; 5.24; 0.0
PRESCRIBED ELEVATIONS : 0.0; 0.0 ;13.0
MASS-BALANCE : YES
TYPE OF ADVECTION : 1;5
SUPG OPTION : 1;0
MASS-LUMPING ON H : 1.
TIDAL FLATS : YES
OPTION FOR THE TREATMENT OF TIDAL FLATS : 1
MATRIX-VECTOR PRODUCT : 2
TREATMENT OF THE LINEAR SYSTEM : 2
SOLVER : 1


THANKS FOR ANSWER.

Hello Xue,

As written in the error message, just before
"PLANTE: PROGRAM STOPPED AFTER AN ERROR
RETURNING EXIT CODE: 2"

"INBIEF (BIEF): NOT A VECTOR MACHINE (ACCORDING TO YOUR DATA)
FROPRO: FRONTAL PRODUCT REQUIRES A
RENUMBERING OF POINTS WITH STBTEL"

This is due to the mesh of your geometry file which has not been built for vector machine, so that MATRIX-VECTOR PRODUCT : 2 is not possible (you can read the TELEMAC-2D reference manual e.g.: "Beware, with option 2, a special numbering of points is required").
Please use the default choice (= 1).

And please do not write posts several times, I have deleted your 2 other messages.

Hope this helps,

Chi-Tuan